![]() ![]() I would even just start with the wiring and see if that takes care of your issue alone. They measured 256k ! New, 5% tolerance matched CTS 500k pots and capacitors woke it up big time. ![]() I recently pulled the stock pots from my 2008 Les Paul Custom. Get a full re-wire kit from The Art of Tone with matched 500k pots, good capacitors and wire. The pay off will be worth it though, in my opinion.Īs far as stock wiring etc. I'm confident you'll make it sound right with the right pickups, it's just up to you to decide whether or not you want to invest the time and energy to do so. If you really dig the look, feel and playability of the guitar, that's sometimes hard to find. It was like night and day and just "clicked." I love the way they look and play, so it was worth the effort to find the right pickups. I have two Les Pauls in particular that just never sounded right until I swapped enough pickups that I was able to find the right combination. I've had several Gibsons that sounded like a "bad" guitar, but the truth was that some pieces of wood are just way more picky about which pickup sounds good in them. I'll swap 3 or 4 different pickups in a guitar in a matter of an hour or so, just to see what I like best in each guitar. I've had a lot of guitars over the years and I'm a notorious pickup swapper. And if I don't find any pickup combo that makes me love the guitar, I can slap the stock stuff back in it! Im open to ideas! But if I go hacking away at it, then its mine! Maybe I get a new wiring harness and pull out all the stock components to experiment. Ive got a 45 day return window and want to check out some different pickups in it. I'm not sure what impact the Gibson PCB and pots play into the tone I'm getting out of the guitar. Still has the tinkyness of a new guitar and string before broken in but I think I dig the way it plays so far. The neck is nice a slim and the action sits nice and low. Hard to describe but they have a fussy kind of mid range and a bit muddy. But, Im not jiving with these 61 pickups. I generally dig vintage hot style pickups through a high gain amp. Ended up pulling the trigger on an Ebony 2018 SG Standard. But the soldering is so basic, it's probably a good project to learn on.So again I got a little GASSY perusing through the online catalogue at Sweetwater. The only real skills required are the ability to solder. No modifications to the existing wiring - no coil taps, etc. So this instructable will be a simple swap of similar humbucking pickups. I would have kept the ESP except it had jumbo frets and that doesn't fit with my style of playing. The guitar itself is a very nice instrument - but the sound with the stock pickups really didn't do anything for me.Īfter a little soul-searching, I remembered I had an ESP with the Seymour Duncan SH-1 (JB) and SH-2 (Jazz) that sounded outstanding. These pickups are supposed to be similar to Seymour Duncan SH-6 Distortion. The guitar I am using for this Instructable is a brand new Hamer Sunburst Q/T (Indonesia) that had "Duncan Designed" HB103B. And based on the number of aftermarket pickups available, a lot of people seem to agree. Why? Because the stock ones always seem lackluster or just don't sound right to me. All of my main guitars have different pickups than the stock ones. 1951 and 42 Experience Tele Set Brand New C 339.08 arcane-inc (1,445) 100 Buy It Now +C 39. Swapping out pickups is one of the easiest ways to drastically change the sound of your guitar. 3x3 Gold Foil Humbucker Distressed Single Pickup Brand New C 250.92 arcane-inc (1,445) 100 Buy It Now +C 33.85 shipping from United States 18+ watchers Sponsored Arcane Inc. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |